Our expertise lies in meeting the fabrication demands of mild steel based portable Cabin. Theseare precision fabricated at our facilities using quality tested steel and are duly welded to providebetter stability. It comprises of entry doors & windows, self-draining roof, base frame, peripheralstructure as per the requirements. Further, eight corners of these Cabin are sufficientlystrengthened to facilitate transportation, lifting and placing operations.The Other Specifications IncludeBase Frame:1. Base frame used are of pressed mild steel channel section2. Main structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’channels section size 75 mm x 40 mmSide and End Walls:1. Side & end frames made out of pressed sections of suitable profiles/pillars of sufficientstrength2. 8 mm MDF board used for interior walls3. All steel sheets used are treated for corrosion resistance4. Vertically corrugated Sheet Panels that are continuously welded to top side and basestructures to offer better strength to weight ratio5. All gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:1. Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of selftapingscrews)2. PVC vinyl flooring fixed on panelRoof1. Interior panelling is done in 8 mm MDF board with adequate insulationPaint:1. Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion freeand fire proof paints)Insulation:1. 25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulationprovided for roofInner Panelling:1. Aesthetically finished Interiors that provide custom built appearance with high qualityworkmanship2. All vertical & horizontal corners neatly and smoothly finished with Aluminium sections3. Panelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:1. The door interiors finished with same material matching with that of bunk house interiors2. Doors provided with locking arrangement with separate handles of both sides of door asrequiredAluminium Windows:1. Aluminium sliding type powder coated windows that are made of aluminium section which is 4mm thick tinted glass.Electrical System:1. Bunk houses provided with concealed electrical copper cables & wiring suitable for 250 volt,50 HZ single phase AC power supply2. Copper cables used are of 3/19 cable for lighting circuits3. ISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit withsmall size distribution board with MCB protection and to separate with main supply.Additional Information Delivery Time 8-10 DAYS Production Capacity As per requirement Interested in this product?Get Latest Price from the sellerContact SellerAbout the CompanyYear of Establishment2011Legal Status of FirmLimited Company (Ltd./Pvt.Ltd.)Nature of BusinessManufacturerNumber of Employees11 To 25 PeopleAnnual TurnoverRs. 2 - 5 CroreIndiaMART Member SinceAug 2010GST27AAACZ5299F1ZWEstablished in the 2009 at Mumbai, Maharashtra, India, we Zigma Cabin Private Limited are one of the leading Manufacturer, Wholesaler and Trader of a wide range of Portable Cabin, Portable Home, Portable Toilet, Portable Bunk House, Security Cabin, Portable Container Our business operations are run by our experts, who has rich experience in our industry sector. The visionary process guidance as well as strong advertising skills provide them to deliver compatible solutions as demanded by our customers. Further, indepth process knowledge regarding involved field areas also allow us to deliver the solutions in highly customized specifications. To Steel Rectangular Modular Portable Bunk ... I agree to the terms and privacy policy Seller Contact DetailsZigma Cabin Private Limited Asfak KhanSurvey No. 61, Gote Ghar Village, Janta Market, Daighar Gaon Mumbai - 400612, Maharashtra, IndiaGet Directionshttps://www.indiamart.com/zigmacabinView Mobile No.Send SMSSend Email

Our expertise lies in meeting the fabrication demands of mild steel based portable Cabin. Theseare precision fabricated at our facilities using quality tested steel and are duly welded to providebetter stability. It comprises of entry doors & windows, self-draining roof, base frame, peripheralstructure as per the requirements. Further, eight corners of these Cabin are sufficientlystrengthened to facilitate transportation, lifting and placing operations.The Other Specifications IncludeBase Frame:1. Base frame used are of pressed mild steel channel section2. Main structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’channels section size 75 mm x 40 mmSide and End Walls:1. Side & end frames made out of pressed sections of suitable profiles/pillars of sufficientstrength2. 8 mm MDF board used for interior walls3. All steel sheets used are treated for corrosion resistance4. Vertically corrugated Sheet Panels that are continuously welded to top side and basestructures to offer better strength to weight ratio5. All gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:1. Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of selftapingscrews)2. PVC vinyl flooring fixed on panelRoof1. Interior panelling is done in 8 mm MDF board with adequate insulationPaint:1. Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion freeand fire proof paints)Insulation:1. 25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulationprovided for roofInner Panelling:1. Aesthetically finished Interiors that provide custom built appearance with high qualityworkmanship2. All vertical & horizontal corners neatly and smoothly finished with Aluminium sections3. Panelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:1. The door interiors finished with same material matching with that of bunk house interiors2. Doors provided with locking arrangement with separate handles of both sides of door asrequiredAluminium Windows:1. Aluminium sliding type powder coated windows that are made of aluminium section which is 4mm thick tinted glass.Electrical System:1. Bunk houses provided with concealed electrical copper cables & wiring suitable for 250 volt,50 HZ single phase AC power supply2. Copper cables used are of 3/19 cable for lighting circuits3. ISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit withsmall size distribution board with MCB protection and to separate with main supply.

Our expertise lies in meeting the fabrication demands of mild steel based portable Cabin. Theseare precision fabricated at our facilities using quality tested steel and are duly welded to providebetter stability. It comprises of entry doors & windows, self-draining roof, base frame, peripheralstructure as per the requirements. Further, eight corners of these Cabin are sufficientlystrengthened to facilitate transportation, lifting and placing operations.The Other Specifications IncludeBase Frame:1. Base frame used are of pressed mild steel channel section2. Main structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’channels section size 75 mm x 40 mmSide and End Walls:1. Side & end frames made out of pressed sections of suitable profiles/pillars of sufficientstrength2. 8 mm MDF board used for interior walls3. All steel sheets used are treated for corrosion resistance4. Vertically corrugated Sheet Panels that are continuously welded to top side and basestructures to offer better strength to weight ratio5. All gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:1. Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of selftapingscrews)2. PVC vinyl flooring fixed on panelRoof1. Interior panelling is done in 8 mm MDF board with adequate insulationPaint:1. Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion freeand fire proof paints)Insulation:1. 25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulationprovided for roofInner Panelling:1. Aesthetically finished Interiors that provide custom built appearance with high qualityworkmanship2. All vertical & horizontal corners neatly and smoothly finished with Aluminium sections3. Panelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:1. The door interiors finished with same material matching with that of bunk house interiors2. Doors provided with locking arrangement with separate handles of both sides of door asrequiredAluminium Windows:1. Aluminium sliding type powder coated windows that are made of aluminium section which is 4mm thick tinted glass.Electrical System:1. Bunk houses provided with concealed electrical copper cables & wiring suitable for 250 volt,50 HZ single phase AC power supply2. Copper cables used are of 3/19 cable for lighting circuits3. ISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit withsmall size distribution board with MCB protection and to separate with main supply.