Find here Bunkhouses, Bunkhouse Cabins manufacturers, suppliers & exporters in India. Get contact details & address of companies manufacturing and supplying

Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''''C'''' channels and cross member is of ''''C'''' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Steel modular portable cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''C'' channels and cross member is of ''C'' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Modular portable site office cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Our expertise lies in meeting the fabrication demands of mild steel based portable Cabin. Theseare precision fabricated at our facilities using quality tested steel and are duly welded to providebetter stability. It comprises of entry doors & windows, self-draining roof, base frame, peripheralstructure as per the requirements. Further, eight corners of these Cabin are sufficientlystrengthened to facilitate transportation, lifting and placing operations.The Other Specifications IncludeBase Frame:1. Base frame used are of pressed mild steel channel section2. Main structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’channels section size 75 mm x 40 mmSide and End Walls:1. Side & end frames made out of pressed sections of suitable profiles/pillars of sufficientstrength2. 8 mm MDF board used for interior walls3. All steel sheets used are treated for corrosion resistance4. Vertically corrugated Sheet Panels that are continuously welded to top side and basestructures to offer better strength to weight ratio5. All gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:1. Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of selftapingscrews)2. PVC vinyl flooring fixed on panelAdditional Information Delivery Time 8-10 ays Production Capacity 1000 Interested in this product?Get Latest Price from the sellerContact SellerAbout the CompanyYear of Establishment2011Legal Status of FirmLimited Company (Ltd./Pvt.Ltd.)Nature of BusinessManufacturerNumber of Employees11 To 25 PeopleAnnual TurnoverRs. 2 - 5 CroreIndiaMART Member SinceAug 2010GST27AAACZ5299F1ZWEstablished in the 2009 at Mumbai, Maharashtra, India, we Zigma Cabin Private Limited are one of the leading Manufacturer, Wholesaler and Trader of a wide range of Portable Cabin, Portable Home, Portable Toilet, Portable Bunk House, Security Cabin, Portable Container Our business operations are run by our experts, who has rich experience in our industry sector. The visionary process guidance as well as strong advertising skills provide them to deliver compatible solutions as demanded by our customers. Further, indepth process knowledge regarding involved field areas also allow us to deliver the solutions in highly customized specifications. To Steel Mobile Portable Cabin, For House I agree to the terms and privacy policy Seller Contact DetailsZigma Cabin Private Limited Asfak KhanSurvey No. 61, Gote Ghar Village, Janta Market, Daighar Gaon Mumbai - 400612, Maharashtra, IndiaGet Directionshttps://www.indiamart.com/zigmacabinView Mobile No.Send SMSSend Email

Our expertise lies in meeting the fabrication demands of Multi Story Portable Cabin. These are precision fabricated at our facilities using quality tested steel and are duly welded to provide better stability. It comprises of entry doors & windows, self draining roof, base frame, peripheral structure as per the requirements. Further, eight corners of these Cabins are sufficiently strengthened to facilitate transportation, lifting and placing operations.Specifications:Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''C'' channels and cross member is of ''C'' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bowsRoofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Multi story portable cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supplyAll electrical wiring are concealed where suitable copper cables are used for lighting circuitsThe copper cables used are of 3/19 cable for lighting circuitsISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''C'' channels and cross member is of ''C'' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Readymade Portable Cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''''C'''' channels and cross member is of ''''C'''' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Modular Portable Cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame: Base frame is made of pressed mild steel channel  The main structural element is of 100 mm x 50 mm 'C' channels and cross member is of 'C' channels section size 75 mm x 40 mm  Side and End Walls: Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets  9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistance  Panels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moisture  Flooring Systems: On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panels Roof: Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulation Paint: Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coats Corrosion free and fire proof paints Insulation: 50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roof Aluminium Windows: Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to it Electrical System: MS Porta Cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame is made of pressed mild steel channelThe main structural element is of 100 mm x 50 mm ''C'' channels and cross member is of ''C'' channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength with exterior wall made up of 1.8 swg M.S specially corrugated sheets9 mm particle board are used for interior walls where steel sheet are treated for corrosion resistancePanels are vertically corrugated with sheets that are continuously welded to top side & base structures so as to offer better strength to weight ratio where all gaps are sealed at edges and at seams, bottom etc to prevent ingress of moistureFlooring Systems:On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring shall be fixed on the panelsRoof:Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows Roofs are adequately cambered for draining of rain water and interior panelling is done in 9 mm particle board with adequate insulationPaint:Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coatsCorrosion free and fire proof paintsInsulation:50 mm thick Rock wool insulation is used for walls & 50 mm thick Rock wool insulation is provided for roofAluminium Windows:Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to itElectrical System:Mild Steel Portable Cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply All electrical wiring are concealed where suitable copper cables are used for lighting circuits The copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply

We are offering Office Porta Cabin to our clients. Also Available In Material Wood FRP

Steel Portable Office Cabin is committed to exceeding customer expectations by providing the highest quality products and services. Our people are dedicated to creating long-term profitable relationships by continually increasing value through reducing variation and eliminating waste in everything we do

With Portable Site Office Cabin we always try to provide our client with exceptional quality portable cabins which are prefabricated and well worked

Our expertise lies in meeting the fabrication demands of mild steel based Portable Control Panel Cabin. These are precision fabricated at our facilities using quality tested steel and are duly welded to provide better stability. It comprises of entry doors & windows, self draining roof, base frame.Specifications:Base Frame:Base frame used are of pressed mild steel channel sectionMain structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’ channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength8 mm MDF board used for interior wallsAll steel sheets used are treated for corrosion resistanceVertically corrugated Sheet Panels that are continuously welded to top side and base structures to offer better strength to weight ratioAll gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of self taping screws) PVC vinyl flooring fixed on panelRoof:Interior panelling is done in 8 mm MDF board with adequate insulationPaint:Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion free and fire proof paints)Insulation:25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulation provided for roofInner Panelling:Aesthetically finished Interiors that provide custom built appearance with high quality workmanshipAll vertical & horizontal corners neatly and smoothly finished with Aluminium sectionsPanelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:The door interiors finished with same material matching with that of bunk house interiorsDoors provided with locking arrangement with separate handles of both sides of door as requiredAluminium Windows:Aluminium sliding type powder coated windows that are made of aluminium section which is 4 mm thick tinted glass.Electrical System:Portable control panel cabin provided with concealed electrical copper cables & wiring suitable for 250 volt, 50 HZ single phase AC power supplyCopper cables used are of 3/19 cable for lighting circuitsISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame used are of pressed mild steel channel sectionMain structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’ channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength8 mm MDF board used for interior wallsAll steel sheets used are treated for corrosion resistanceVertically corrugated Sheet Panels that are continuously welded to top side and base structures to offer better strength to weight ratioAll gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of self taping screws) PVC vinyl flooring fixed on panelRoof:Interior panelling is done in 8 mm MDF board with adequate insulationPaint:Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion free and fire proof paints)Insulation:25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulation provided for roofInner Panelling:Aesthetically finished Interiors that provide custom built appearance with high quality workmanshipAll vertical & horizontal corners neatly and smoothly finished with Aluminium sectionsPanelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:The door interiors finished with same material matching with that of bunk house interiorsDoors provided with locking arrangement with separate handles of both sides of door as requiredAluminium Windows:Aluminium sliding type powder coated windows that are made of aluminium section which is 4 mm thick tinted glass.Electrical System:Ms portable cabin provided with concealed electrical copper cables & wiring suitable for 250 volt, 50 HZ single phase AC power supplyCopper cables used are of 3/19 cable for lighting circuitsISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame:Base frame used are of pressed mild steel channel sectionMain structural element are of ‘C’ Channels 100 mm x 50 mm and cross member is of ‘C’ channels section size 75 mm x 40 mmSide and End Walls:Side & end frames made out of pressed sections of suitable profiles/pillars of sufficient strength8 mm MDF board used for interior wallsAll steel sheets used are treated for corrosion resistanceVertically corrugated Sheet Panels that are continuously welded to top side and base structures to offer better strength to weight ratioAll gaps sealed at edges & at seams, bottom etc for preventing ingress of moistureFlooring Systems:Bottom frame provided of 18 mm thick plywood, bison panel/E board (fixed by means of self taping screws) PVC vinyl flooring fixed on panelRoof:Interior panelling is done in 8 mm MDF board with adequate insulationPaint:Epoxy Zinc Phosphate primer and synthetic Epoxy paints used for final 2 coats (Corrosion free and fire proof paints)Insulation:25 mm thick Glass wool insulation used for walls as well as 50 mm thick Glass wool insulation provided for roofInner Panelling:Aesthetically finished Interiors that provide custom built appearance with high quality workmanshipAll vertical & horizontal corners neatly and smoothly finished with Aluminium sectionsPanelling of side walls & roof is of 8 mm thick decorative laminated MDF boardMain Entry Door:The door interiors finished with same material matching with that of bunk house interiorsDoors provided with locking arrangement with separate handles of both sides of door as requiredAluminium Windows:Aluminium sliding type powder coated windows that are made of aluminium section which is 4 mm thick tinted glass.Electrical System:Modular Porta Cabin provided with concealed electrical copper cables & wiring suitable for 250 volt, 50 HZ single phase AC power supplyCopper cables used are of 3/19 cable for lighting circuitsISI mark & concealed PVC conduits insulated copper wire used for wiring in PVC conduit with small size distribution board with MCB protection and to separate with main supply

Base Frame: Base frame is made of pressed mild steel channel section where main structural element is of 100 mm x 50 mm and cross member is of 'C' channels section size 75 mm x 40 mm Flooring Systems: On bottom frame 18 mm thick plywood, bison panel/E board is fixed by means of self taping screws and PVC vinyl flooring is fixed on the panel Roof: Self draining type roof is provided using 1.8 swg thick M.S. sheet with adequate roof bows that are adequately cambered for draining of rain water Interior panelling is done in 9 mm particle board with adequate insulation Paint: Epoxy Zinc Phosphate primer & synthetic Epoxy paint is used for final 2 coats (Corrosion free and fire proof paints) Main Entry Door: Doors shall be of external opening type made out of same material as wall panels with door closing units (Construction of doors is of double skin steel construction with 40 mm thick Rock wool insulation) The peripheral edges of doors are sealed with double gaskets to make it waterproof & leak proof and the interiors are finished with same material matching with that of bunk house interiors The doors are provided with locking arrangement with separate handles of both sides of door as required with the main door insulated and fitted with Godrej mortise lock and power bolt Aluminium Windows: Aluminium sliding type powder coated windows provided that are made of aluminium section, 5 mm thick, tinted glasses are to be fitted to it Electrical System: MS Prefabricated Portable Cabin provided with electrical wiring suitable for 250 volt, 50 HZ single phase AC power supply with all electrical wiring well concealed Suitable copper cables are used for lighting circuits where copper cables used are of 3/19 cable for lighting circuits ISI mark & concealed PVC conduits insulated copper wire are used for wiring required to be done in PVC conduit with small size distribution board with MCB protection and to separate with main supply